JET 414453 Manuale di Manutenzione e Cura

Operating Instructions and Parts Manual 5-inch x 8-inch Horizontal Band Saw Models: J-3130, J-3230 Model J-3130 shown WALTER MEIER (Manufacturi

109.0 Operating Instructions 9.1 Clamping materials in the vise Refer to Figure 1. 1. Lift the saw arm to its full up position. 2. Lock the arm u

11 Figure 9: Using the scale on the rear of the saw base to set the jaws for angle sawing. Where the edge of the right jaw crosses the scale an app

122. Disconnect the saw from its electrical power source. 3. With the arm in its fully lowered position, remove the pulley cover lock screw and ope

139.11 Blade break-in procedures New blades are very sharp, and therefore have a tooth geometry which is easily damaged if a careful break-in proced

14cover and remove the three wires which connect it to the power cable. 6. Remove the four nuts, bolts and washers which hold the motor to its mount

1513. Check with a paper strip to be certain the blade has not moved back into contact with the flange. Readjust, if necessary. 14. Using the blade

162. Adjust the guide bearings according to instructions in sect. 10.2, Adjusting guide bearings. 3. Adjust the back-up bearing according to instru

1711.0 Maintenance Chart Item Action Interval Comments Wheel, guide or back-up bearings Inspect for leakage Daily All bearings are sealed – any

1812.0 Troubleshooting the J-3130 and J-3230 Table 4 Symptom Possible Cause Correction Excessive blade breakage. Material loose in the vise. Use m

19Symptom Possible Cause Correction Premature blade dulling. (cont.) Incorrect coolant or no coolant. Check with materials supplier and/or b

2 1.0 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of o

20Symptom Possible Cause Correction Blade twisting. (cont.) Incorrect guide bearing adjustment Adjust guide bearings according to instructions in th

2113.0 Replacement Parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848 Mo

2213.1.1 Lower Saw Head – Exploded View

2313.1.2 Lower Saw Head – Parts List Index No Part No Description Size Qty 01...5631421 ... Hex head Screw ..

2413.2.1 Upper Saw Head – Exploded View

2513.2.2 Upper Saw Head – Parts List Index No Part No Description Size Qty 01...5630221 ... W asher ...

2613.3.1 Saw Base – Exploded View

2713.3.2 Saw Base – Parts List Index No Part No Description Size Qty 01...5630221 ... W asher ...

28Index No Part No Description Size Qty 57...HBS56S-259 ... Cylinder Upper support (serial #11110606 and higher) ...

2913.4.1 Stand and Coolant System – Exploded View

3 2.0 Table of contents Section Page 1.0 Warranty and Service ...

3013.4.2 Stand and Coolant System – Parts List Index No Part No Description Size Qty 01...5631431 ... Hex nut .

31This page intentionally left blank.

32 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-2

4 3.0 Safety Warnings General Cautions - Misuse of this machine can cause serious injury. - For safety, the machine must be set up, used and se

5 18. Keep hands in sight and clear of all moving parts and cutting surfaces. 19. All visitors should be kept at a safe distance from the work area

6 4.0 About this machine and manual The JET 5”x8” Band Saw is available as a dry cutting saw or a wet cutting saw. If required, a dry cutting band s

7 6.0 Specifications Model numbers ... J-3130 ...

8 7.0 Set-up and assembly Read and understand all assembly instructions before attempting assembly. Failure to comply may cause serious injury. 7.

9 7.3 Installing coolant kit Refer sect. 13.4.1 for a complete view of the components in the coolant kit, and refer to Figure 6 for the attachment o